Large, tall, long, easy, hot, big, cold, nice, bad, strong, short, wide, good, happy, high, low, busy, well, little, many, far
С инфинитивом без частицы to после глаголов
Elastomers are similar to thermoplastics but have sufficient cross-linking between molecules to prevent stretching and creep
RESINS
BASIC PRINCIPLES OF WELDING
GEAR
CONSTRUCTION OF AN AUTOMOBILE
TWO-STROKE AND DIESEL ENGINES
AC MOTORS
AUTOMATION IN INDUSTRY. FIXED AND PROGRAMMABLE AUTOMATION
HISTORY OF ROBOTICS
COMPUTERS
Навигация
TWO-STROKE AND DIESEL ENGINES
English language for technical colleges
393037
знаков
13
таблиц
0
изображений
10. TWO-STROKE AND DIESEL ENGINES
Most diesels are also four-stroke engines. The first or suction stroke draws air, but no fuel, into the combustion chamber through an intake valve. On the second or compression stroke the air is compressed to a small fraction of its former volume and is heated to approximately 440°C by this compression. At the end of the compression stroke vaporised fuel is injected into the combustion chamber and burns instantly because of the high temperature of the air in the chamber. Some diesels have auxiliary electrical ignition systems to ignite the fuel when the engine starts and until it warms up. This combustion drives the piston back on the third or power stroke of the cycle. The fourth stroke is an exhaust stroke.
The efficiency of the diesel engine is greater than that of any petrol engine and in actual engines today is slightly over 40 per cent. Diesels are in general slow-speed engines with crankshaft speeds of 100 to 750 revolutions per minute (rpm) as compared to 2,500 to 5,000 rpm for typical petrol engines. Some types of diesel, however, have speeds up to 2,000 rpm. Because diesels use compression ratios of 14 or more, they are generally more heavily built than petrol engines, but this disadvantage is counterbalanced by their greater efficiency and the fact that they can be operated on less expensive fuel.
Two-Stroke Engines
By suitable design it is possible to operate a diesel as a two-stroke or two-cycle engine with a power stroke every other stroke of the piston instead of once every four strokes. The efficiency of such engines is less than that of four-stroke engines, and therefore the power of a two-stroke engine is always less then half that of a four-stroke engine of comparable size.
The general principle of the two-stroke engine is to shorten the periods in which fuel is introduced to the combustion chamber and in which the spent gases are exhausted to a small fraction of the duration of a stroke instead of allowing each of these operations to occupy a full stroke.
In the simplest type of two-stroke engine, the valves are the openings in the cylinder wall that are uncovered by the piston at the end of its outward travel. In the two-stroke cycle the fuel mixture or air is introduced through the intake port when the piston is fully withdrawn from the cylinder. The compression stroke follows and the charge is ignited when the piston reaches the end of this stroke. The piston then moves outward on the power stroke, uncovering the exhaust port and permitting the gases to escape from the combustion chamber.
11. DIRECT-CURRENT (DC) GENERATORS
If an armature revolves between two stationary field poles, the current in the armature moves in one direction during half of each revolution and in the other direction during the other half. To produce a steady flow of unidirectional, or direct, current from such a device, it is necessary to provide a means of reversing the current flow outside the generator once during each revolution. In older machines this reversal is accomplished by means of a commutator (коллектор) — a split metal ring mounted on the shaft of the armature. The two halves of the ring are insulated from each other and serve as the terminals of the armature coil. Fixed brushes of metal or carbon are held against the commutator as it revolves, connecting the coil electrically to external wires. As the armature turns, each brush is in contact alternately with the halves of the commutator, changing position at the moment when the current in the armature coil reverses its direction. Thus there is a flow of unidirectional current in the outside circuit to which the generator is connected. DC generators are usually operated at fairly low voltages to avoid the sparking between brushes and commutator that occurs at high voltage. The highest potential commonly developed by such generators is 1500 V. In some newer machines this reversal is accomplished using power electronic devices, for example, diode rectifiers.
Modern DC generators use drum armatures that usually consist of a large number of windings set in longitudinal slits in the armature core and connected to appropriate segments of a multiple commutator. In an armature having only one loop of wire, the current produced will rise and fall depending on the part of the magnetic field through which the loop is moving. A commutator of many segments used with a drum armature always connects the external circuit to one loop of wire moving through the high-intensity area of the field, and as a result the current delivered by the armature windings is virtually constant. Fields of modern generators are usually equipped with four or more electromagnetic poles to increase the size and strength of the magnetic field. Sometimes smaller interpoles are added to compensate for distortions in the magnetic flux of the field caused by the magnetic effect of the armature.
DC generators are commonly classified according to the method used to provide field current for energizing the field magnets. A series-wound generator has its field in series with the armature, and a shunt-wound generator has the field connected in parallel with the armature. Compound-wound generators have part of their fields in series and part in parallel. Both shunt-wound and compound-wound generators have the advantage of delivering comparatively constant voltage under varying electrical loads. The series-wound generator is used principally to supply a constant current at variable voltage. A magneto is a small DC generator with a permanent-magnet field
Похожие работы
... compound-shortened word formed from a word combination where one of the components was shortened, e.g. «busnapper» was formed from « bus kidnapper», «minijet» from «miniature jet». In the English language of the second half of the twentieth century there developed so called block compounds, that is compound words which have a uniting stress but a split spelling, such as «chat show», «pinguin ...
... of job. Because I suppose if than marriage he must provide his family. And the young coups must that they meant for understand each other. Customs and holidays in English – speaking countries. - Customs and holidays in the urban community are of great importance for everyone. - I think no matter who the man might be he must know customs and holidays his country. What holidays do you ...
... was the first writer in Europe to formulate communist principals as a bases of society. The Renaisense in England. The prideses of Shakespeare. The most brilliant period of English literature was in the second half of the 16’th and begining of 17’th centure.Sometimes it’s called “Elizabethen age” after quen Elizabeth 5. England had become a geat world ...
... like that: what kinds of animals eat grass?» The boy brightened up. «Animals!» he exclaimed, «I thought you said admirals.» Unit 9 Grammar: 1. Passive Voice. 2. Пассивные конструкции характерные для английского языка. 3. Формы инфинитива. I. Language Practice 1. Practise the fluent reading and correct intonation: — Helölo, Tom! — Helølo, Nick ö. Here you ø are at ...
0 комментариев